135 Degree Hydraulic Soft Close Cabinet Door Hinge - F726

Product Overview — F726 135° Hydraulic Soft Closing Cabinet Door Hinge

TheF726 135 degree hydraulic cabinet hinge is a wide-angle concealed cabinet hinge with a built-in hydraulic damper that closes the door slowly and silently. Its arm geometry opens to 135° instead of the ordinary 95–105°, so the door swings far wider and gives clear access to the inside of the carcass, while the integrated piston in the hinge cup pulls the last part of the travel closed without slam, bang or rebound. For kitchen, wardrobe and furniture programs where the buyer specifies soft closing as standard, this 135 degree hinge delivers the wide opening and the controlled close in one concealed hingeunit.

Guangzhou Gorgeous Intelligent Technology Co., Ltd. builds this wide angle soft close hinge from cold rolled steel plate with a nickel plated finish, on the same concealed cabinet hinge set-out used across our furniture hinge range. That means your boring gauge, your front set-out and your assembly instructions stay unchanged — the only difference your line will notice is a door that opens wider and closes itself quietly, which is exactly what retail customers expect from a modern cabinet hinge.

F726 135° hydraulic cabinet hinge — hinge cup, wide-angle arm and mounting base with adjustment screws

Why 135 Degrees and Why Hydraulic

A standard cabinet hinge stops around 100°, which is enough to load a shelf but not enough to keep the door leaf clear of the adjacent panel or handle. The 135° geometry of this wide angle cabinet hinge lays the door back further, so pull-out baskets, cutlery trays, corner units and display cabinet interiors become fully reachable, and the door no longer springs back toward the opening when it is pushed hard. On tall wall units the extra swing also reduces the risk of the door corner striking the neighbouring door or the appliance in front.

The hydraulic element is separate from the swing angle and solves a different problem. Inside the hinge cup a small piston damps the final closing arc: past a certain angle the door free-swings normally, and as it approaches shut the damper takes over so the hinge closes under control. That removes the slam noise, the shock load on the screw fixings and the chipboard fatigue that shorten the life of an undamped cabinet hinge in daily-use furniture.

Key Features and Benefits

• 135° wide opening — the arm clears a much larger arc than a normal cabinet hinge, giving full access to the cabinet interior.
• Integrated hydraulic damper — soft, silent closing built into the hinge cup; no separate damper box to buy, stock or fit.
• No rebound or slam — the damped hinge protects door edges, carcass fixings and hinge screws from impact fatigue.
• Cold rolled steel construction (Q195–Q235) — plate pressing holds the wide-angle hinge geometry so the door stays square over its life.
• Nickel plated finish — consistent colour across cup, arm and base of each hinge set; resistant to handling marks.
• Clip-on detachable joint — the door lifts off this cabinet hinge without tools for cleaning, adjustment and service.
• Three-dimensional adjustment — lateral, depth and height adjustment on the hinge base after the door is hung.
• Overlay options — full overlay, half overlay and inset cranking available on the same 135° hingeplatform.
• Consistent set-out — bores on the standard concealed hinge gauge, so existing machinery and templates still apply.
• OEM / ODM accepted — logo marking on the hinge, custom plating, custom screws and retail or bulk packing.

Technical Specifications

The figures above are manufacturing reference values for the F726 135 degree hydraulic hinge. Damper strength is matched to door weight and height, so we confirm the specification against your door schedule before volume production of this cabinet hinge.

The 135° opening of this wide angle cabinet hinge laid right back, keeping the door clear of the opening

Matching the Damper to the Door

A hydraulic hinge that is too strong for a light door will make it close slowly and feel lifeless; one that is too weak for a heavy door will not control the close at all. Before quoting this 135 degree cabinet hinge we therefore ask for door height, door width, panel material and approximate door weight, then confirm whether the standard damped hinge cup is correct or whether the door needs an additional hinge purely to carry the load. Tall and heavy doors are the usual case where the damper specification on a soft close hinge has to be reviewed rather than assumed.

Material, Plating and Durability

The F726 135 degree hydraulic hinge is pressed from cold rolled steel, because a wide-angle hinge carries its load through a longer moment arm than a standard cabinet hinge and any play in the knuckle becomes visible as door sag within months. Cup wall, arm thickness and knuckle rivet are controlled per pressing lot. The plating is nickel over a copper undercoat on all visible surfaces of the hinge, chosen so the cup, arm and base of one set match in colour and so the finish tolerates the humidity seen in kitchens and bathrooms.

The damper itself is a sealed piston unit inside the hinge cup. Because it is sealed, it is not affected by dust or cabinet cleaning products, and because it sits inside the cabinet hinge rather than on the carcass, it cannot be lost during assembly and it needs no extra boring operation on the panel.

Installation Procedure

1. Plan the hinge positions. Put the top and bottom hinge 100–150 mm from the door corner; on wide doors add intermediate hinges so the load, not the damper, carries the door weight.
2. Drill the cup bore to the depth confirmed for your panel, using a sharp bit so the facing is not lifted around the hingeseat.
3. Fit the hinge cup and drive the two supplied screws through the cup flange.
4. Screw the base to the carcass side panel into the slotted holes, keeping lateral adjustment free.
5. Clip the door on — press the hinge arm onto the base until the release clip seats positively.
6. Set the alignment with the lateral and depth screws on the hinge base, then tighten the base screws.
7. Test the damping. Push the door from half open; the damped cabinet hinge should take over and close it without any bang at the end of travel.
8. Check the full swing. Open to the 135° stop and confirm the door clears the adjacent panel, handle or appliance throughout the arc of the hinge.

Front elevation of the hinge — cup, wide-angle arm, base and the two adjustment screws

Where the 135° Hinge Is the Right Choice

• Kitchen wall and base units with pull-out baskets, magic corner units or cutlery trays
• Wardrobe and closet doors where the opening has to be fully clear for hanging access
• Bathroom vanities and laundry cabinets in daily-use housing projects
• Retail display cabinets, museum and exhibition joinery needing wide, controlled access
• Office furniture, medical cabinets and laboratory casework where silent closing is specified
• Hospitality furniture, where doors are closed hundreds of times a day and an undamped hinge fails early
• Accessibility projects, where a self-closing cabinet hinge helps users who cannot close a door firmly

OEM, ODM and Wholesale Programme

This135 degree hydraulic cabinet hinge is produced for hardware brands, importers, distributors and furniture factories under their own specification. We can stamp or laser-mark your logo on the hinge cup and arm, change plating colour and salt-spray grade, supply alternative screws for chipboard, MDF, ply or aluminium profiles, and pack the hinge in bulk inner boxes, colour boxes, blister cards or shelf-ready retail packaging with your barcode. Customer-specific hinge tooling is never sold to a third party, and drawings are handled under NDA when required.

Quality Control

• Material — steel grade, strip thickness and hardness verified per heat lot before the hingedies.
• Pressing — cup dimensions, arm profile and knuckle alignment sampled for every wide-angle hingebatch.
• Damper — closing-time sampling on the assembled hinge, so the soft-close arc is consistent between cartons.
• Plating — coating thickness, adhesion cross-cut and colour match across cup, arm and base.
• Corrosion — neutral salt spray sampling against the agreed protection grade.
• Cycling — automated open-close life testing of the cabinet hinge, logged per production lot.
• Pre-shipment — AQL inspection on quantity, accessories, packing and appearance; third-party inspection welcome.

Quality system certification covering cabinet hinge and furniture fitting production

Packaging and Delivery

Standard packing of the F726 soft close hinge is one hinge cup, one base and the matching screws per polybag, ten bags per inner box, one hundred pieces per export carton, with desiccant and an ocean-freight rated outer. Because the damper is internal, the hinge packs flat with no loose damper parts to lose. Loose, colour box, blister and custom carton printing are available, and packing list with cube and gross weight is issued at quotation stage.

Export packing and container loading preparation

Manufacturing Capability

Our works run progressive-die pressing, robotic welding, automated plating and CNC machining across the ranges we supply, including concealed cabinet hinges, drawer slides, handles, legs, castors and architectural stainless fittings. Supplying the hinge and the rest of the furniture fittings from one factory keeps the finishes matched and lets us consolidate a full hardware package on one shipment.

Production and CNC workshop

OEM / ODM development for hardware brands and furniture factories

Meeting buyers at international furniture and building-materials exhibitions

Frequently Asked Questions

Q1. Is the damper built into this hinge or added separately?
Built in. The piston sits inside the hinge cup, so this is a single-component soft close cabinet hinge with no separate damper box to purchase, stock or press-fit on the line.

Q2. Does 135 degrees require different drilling?
No different bore. The 135° geometry is in the arm and knuckle of the hinge; the cup bore stays on the standard concealed hinge gauge, so your existing set-out still applies.

Q3. Will the damper stop working after a few years?
The damper is a sealed unit and is life-tested on our cycle rig before the hinge ships. If a project specifies a higher cycle count, tell us at quotation and we will confirm the tested figure for this soft close hinge rather than guess.

Q4. Can I use fewer hinges because the door opens wider?
No. Opening angle and load capacity are separate properties of a cabinet hinge. Size the hinge count from door height and weight, and use the 135° swing to gain access, not to reduce fixings.

Q5. Which overlay should I order?
Full overlay when one door covers the whole side panel, half overlay when two doors share a panel, inset when the door sits inside the opening. Send the elevation and we will set the cranking on each hinge line of your schedule.

Q6. Do you offer this hinge in stainless steel?
This listing is the standard cold rolled steel nickel plated hinge. For marine, RV or high-humidity programs we quote the equivalent specification in stainless steel or with a reinforced plating build-up on request.

Contact and Next Steps

If your program needs a wide-angle, self-closing 135 degree hydraulic cabinet hinge in cold rolled steel with nickel finish, the F726 is tooled for volume output and available for sample dispatch. Send the door height, width, material, weight, required overlay and annual quantity, and we will return a quotation with the drilling template, damper specification, screw selection, packing data and container loading plan for this soft close cabinet hinge, together with matching cabinet hinges from our wider furniture hinge range.