0
image
image
image
image
iron corner bracket

Iron Corner Bracket 40 mm Legs 15.6 mm Wide G-001

G-001
G-001 is a small iron corner bracket with 40 mm legs at a right angle, 15.6 mm wide, two holes in each leg and rounded outer ends, for drawer boxes, cabinet backs and light furniture repairs.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The G-001 Iron Corner Bracket

G-001 is the smallest kind of corner fitting there is: a strip of iron folded once to a right angle, with two holes either side of the fold and the outer ends rounded off. It is 15.6 mm wide with 40 mm legs, so it sits inside a drawer box, behind a cabinet back, or across a joint that has opened, without needing the clearance a heavier plate would.

It is a light-duty bracket and it is priced and packed as one. The value is in the fit: two holes per leg rather than one, so the joint cannot rotate about a single screw, and a width that lands on the timber rather than beside it.

G-001 iron corner bracket with 40 mm legs and two holes per leg, three quarter view

What The Four Holes Do

Two holes in each leg make a bolted joint instead of a pivoted one. With one hole per leg, a corner is held by nothing but friction, and the whole joint swings around the two screws the first time the piece is dragged. With two per leg, each face is fixed along a line, and the bracket resists that rotation in both directions.

The hole pattern is also what separates this from the smallest brackets in the range, which carry a single hole per leg. That version is for locating a panel; this one is for holding a joint that will be worked.

One leg of the G-001 bracket face on, two punched holes and the rounded end

Why The Width Is 15.6 mm

The width is the number that decides whether the bracket fits the job, more than the leg length does. At 15.6 mm it sits inside a drawer side, on the face of a cabinet back or along a bed slat rail without overhanging into the space the drawer or the mattress needs. A wider plate in the same corner will foul the drawer box before the drawer is even closed.

It is also wide enough to take two screws across the member rather than down its centreline. Screws on the centreline of a thin board are the ones that split it; screws either side of the centre have sound material around them.

Iron, And What That Means In Service

Iron is the honest material for a bracket of this size. It is stiff for its thickness, it folds cleanly, and it takes a plated finish well, which is what the bright silver surface in these frames is: a plated skin over the iron rather than a different metal underneath.

The finish is the part that decides where the bracket can go. Indoors, in a dry cabinet or a drawer box, a plated bracket outlasts the furniture. In a bathroom, a kitchen splash zone or anywhere outdoors, the plating is what fails, and it fails at the hole edges and along the fold, because those are the places the coating is thinnest and water sits longest. If the job is wet, say so at enquiry and the plating can be discussed before packing rather than after a season of rust.

Two practical notes on iron. A scratched bracket will rust at the scratch, so do not slide a bundle across a concrete floor. And do not leave the parts in the carton in a damp store: iron in a sealed carton with moisture in it will spot before it is ever fitted.

G-001 iron corner brackets arranged as a small pack, rounded ends and hole rows visible

Where A Bracket This Size Fits

The four uses that come up most often are all light joints in furniture that is already built or being assembled by hand:

  • Drawer boxes, where the sides meet the front and the joint has to stay square while the drawer is pulled.
  • Cabinet backs and thin panels, where a wider plate would show through or foul the carcass.
  • Bed slat rails and headboard cleats, as a light repair bracket rather than the main structural corner.
  • Small carcass repairs, picture frames and display work, where the bracket has to disappear behind the face rather than sit on it.

In each case the bracket is doing one of two jobs: keeping a joint square during assembly, or pulling a joint that has already opened back together. It is worth being clear which one you are buying for, because the repair job needs the holes to land on sound material either side of the split, and that decides whether the 40 mm leg is long enough.

Fitting It Without Splitting The Board

Drill pilots. Iron this thin will take a self-tapping screw without a pilot, but the timber behind it will not, and a chipboard edge will split whether or not the bracket survives. A pilot slightly smaller than the screw shank, drilled through the bracket holes so the positions are exact, is the whole technique.

Hold the bracket in place with one screw, check the angle with a square, then drill and drive the other three. Working from one corner outwards keeps the joint from creeping as the screws pull.

Do not over-tighten. The bracket is thin enough that a driver will pull it into the board and crush the surface around each hole, and a crushed hole holds nothing. Tighten until the bracket touches, then stop.

Two brackets per joint is not the rule either. One is a corner; two, either side of a member, is a strap. Where the joint has already split, bracket the sound material on both sides rather than spanning the split with one bracket, because a bracket across a split is a clamp on a gap.

Use plated or stainless screws to match. A bright zinc screw in a plated bracket is fine indoors; a black drywall screw is not, because the two finishes will react and the screw will bleed rust down the bracket within a season.

What These Are Called

Three phrases bring this part in, and all three describe exactly what is in these frames. An iron corner bracket is the material plus the shape, and it is what a buyer asks for when the finish has to be specified as iron rather than steel or plastic. A 40mm L bracket is the size-led phrase, used by someone who has measured the gap and wants the leg length, which is the number that decides whether the bracket reaches sound material on both faces.

The third is a job description. A bed frame corner bracket is what a customer searches for when a frame has started to rock at the joint; the bracket is the same part, and it is the reason a small bracket like this sells in packs rather than singly. None of the three phrases names a finish or a coating, so the plating has to be confirmed on the order.

A Small Bracket Is Not A Structural Hanger

It is worth saying plainly, because this is the size that gets asked to do too much. A folded iron bracket at this size is for a light joint: a drawer, a panel, a repair. It is not a joist hanger, not a gate hinge, not a load path for a shelf carrying tools, and not something to hang a chair from. Those need a welded or cast fitting with a stated working load.

The same applies to a bed frame. On a frame that has started to rock, this bracket will tighten a slat rail, a headboard cleat or a corner that has worked loose. It will not carry the corner load of a broken rail on its own, and a frame repaired that way will fail again at the first move.

Checking A Delivery

Four checks, all quick. The angle: stand the bracket on one leg and sight the other against a square, because a corner that has sprung open in the press is difficult to pull back without marking the finish. The faces: flat, with no oil-canning between the holes. The ends: evenly rounded, with no shear line left across the radius where a finger can catch it. The holes: deburred on the face that meets the timber, since a burr on iron will stop the bracket seating and leave a gap that shows.

Then count. Packs of these are counted by weight on some lines, and a short pack is the most common complaint on a small bracket. Ask for the count to be stated on the carton.

Packing And Ordering

The brackets are supplied bagged or boxed to a count, and they can be mixed with other sizes in one carton for a distributor. Because they are small and light, freight is rarely the issue; the issue is counting and handling, so a bag with the count printed on it is worth asking for.

Order by the leg length and the width, and state the finish and the environment. Those four answers fix the part; anything else can be agreed afterwards.

The Drawing, Read Out

The size drawing in the gallery shows the three lengths this corner is made in. The member in this listing is the long one: 40 mm on both legs, 15.6 mm wide, two holes per leg and the outer ends rounded.

FigureValueWhat it decides
Leg length40 mmreach either side of the fold
Width15.6 mmfits inside a drawer side or a cabinet back
Holestwo per legthe joint is fixed along a line, not at a point
Endsroundedno sharp corner on a part that is handled

The Fold Is The Part That Decides

A folded bracket is only as good as the radius of its fold. A tight fold work-hardens the iron along the corner of the bracket, which is where the bracket is stiffest and also where a crack will start if the tool is blunt. A slightly open radius spreads that strain and gives the bracket a fillet of material inside the corner, which is what stops the bracket tearing when the joint is pulled.

The practical test is visual: hold the bracket up to a light and look along the inside of the fold. An even line with no bright crack or step means the bracket was folded with the tool set correctly. A bright line along the inside means the iron has been stretched to the point of splitting, and that bracket will fail at the fold long before it fails at a screw.

When A Wider Plate Is The Better Answer

This bracket is not the answer to every corner, and saying so saves a return. If the member the bracket lands on is much wider than the bracket, the two screws sit near the centre and the ends of the member are left unsupported; a wider plate does that job better. If the corner is carrying load rather than holding a joint, a thicker welded bracket is the right part. And if the two faces are not at a right angle, no folded bracket will fit, however carefully it is drilled.

What this bracket does better than a wider plate is fit: inside a drawer box, behind a back panel, along a slat rail. That is the trade, and it is why the same corner is made in several widths rather than one.

A Repair, In Order

On a joint that has already opened, close it first and hold it closed with a clamp before the bracket goes on. A bracket screwed across an open joint will hold the gap open, and the screws through the bracket will work loose as the piece is used. Clamp, check the faces are flush, then mark through the bracket holes.

If the original screw holes are oval, move the bracket rather than reusing them. Two fresh pilots through the bracket into sound material either side of the damage will hold; a screw dropped back into an oval hole will not, whatever bracket is over it.

Why A Small Bracket Sells In Packs

Nobody buys one of these. A cabinet shop fitting out a run of drawer boxes needs brackets by the hundred, and a household fixing a rocking frame needs a handful and will not drive across town for two. That is why the bracket is bagged to a count and why the count is printed on the bag: the bracket is cheap, the handling is not.

Mixed cartons are normal for a distributor: several lengths of this corner plus a bag of screws in one carton. If the mix matters, list it line by line on the order rather than describing it, because a mixed carton of brackets is counted by hand.

Frequently Asked Questions

What thickness is the iron?

The frames in this listing do not print a thickness, so the gauge is quoted on the order rather than guessed here. Give the load and the screw size and the bracket can be matched to them; a bracket quoted at a thickness nobody measured is how a thin part ends up on a heavy joint.

Is it iron or stainless steel?

Iron, with a bright plated finish, which is the surface in every frame on this page. Stainless is a different bracket for a different job and is not what this listing ships. If the installation is wet, say so and the plating or the material can be discussed before the bracket is packed.

What exactly does 15.6 mm measure?

The width of the strip the bracket is folded from, across the face the screws go through. The 40 mm figure is the length of each leg away from the fold. Width decides whether the bracket fits inside a drawer side or a cabinet back; leg length decides how far it reaches either side of the joint.

Will one bracket hold a bed frame?

Not on its own. This bracket will tighten a slat rail, a headboard cleat or a corner that has worked loose, and it is the size people buy for that repair. It will not carry the corner load of a broken rail, and a frame held together by one small bracket will fail again as soon as it is moved.

Can the bracket be supplied unplated or powder coated?

Yes, where the bracket is going to be coated with the frame it is fitted to, unplated parts are the usual request. Say so on the order; the bracket is made to order anyway, so the finish is decided before folding rather than after.

How many brackets are in a bag or a carton?

The count is agreed on the order and printed on the bag, because a small bracket is counted by weight on some lines. A bracket that arrives short is the most common complaint at this size, and a printed count is the cheapest way to avoid it.

Do the two legs have to be at exactly ninety degrees?

Yes, and that is the first thing to check on delivery. A folded bracket that has sprung open in the press is difficult to correct on site without marking the finish, and a bracket a couple of degrees off will pull a carcass out of square as it is tightened.

Can I see a sample before ordering?

Ask for one with the enquiry and state the finish you intend to use. A sample bracket is the only reliable way to confirm the fold, the hole positions and the plating, because a photograph of a bright plated bracket flatters the surface.

G-001 is an iron corner bracket with 40 mm legs, 15.6 mm wide, two holes per leg and rounded ends, packed to a count.

State the leg length, the width, the finish and whether the job is dry or wet, and the bracket can be checked against the piece before anything is packed.

Who Makes The Bracket

G-001 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name. The company runs three production bases in Guangdong, folds and plates this bracket in house, and has been exporting small hardware to importers, distributors and own-brand programmes for eighteen years.

The panels below are the plant and the paperwork behind every bracket on this page: the factory that folds this bracket, the certificates, the showroom, the exhibitions, the cartons and the delivery schedule. They are the part of the listing that answers a new supplier question, and the reason a repeat order does not need to ask it again about this bracket.

Two of them are worth reading before you order a bracket of this size. The certificate panel sets out what the quality system covers, and the packing panel sets out the four carton options a distributor can choose between when the bracket is going out under someone else's label.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand