0
image
image
image
image
stainless steel L bracket

Stainless Steel L Bracket 16 mm Wide Four Sizes G-JM21

G-JM21
G-JM21 is a stainless steel L bracket 16 mm wide and 2 mm thick, folded to a right angle, with 19, 24, 29 and 39 mm legs, rounded tails and one hole per leg, for drawer boxes, cabinet backs and light rack work.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The G-JM21 Stainless L Bracket

G-JM21 is a stainless steel L bracket, 16 mm wide and 2 mm thick, folded once to a right angle with the tail ends rounded. It is made in four leg lengths: 19 mm, 24 mm, 29 mm and 39 mm.

G-JM21 stainless steel L bracket, two brackets stacked, rounded tails and one hole per leg

At A Glance

ItemG-JM21
MaterialStainless steel
Width16 mm
Leg lengths19 mm, 24 mm, 29 mm, 39 mm
Thickness2 mm
HolesOne per leg, two in the long leg of the 39 mm
EndsRounded tail
Angle90 degrees

Which Length For Which Job

The bracket leg length follows the member it lands on, not the load.

  • 19 mm for a drawer box corner, where the strip must clear the runner.
  • 24 mm and 29 mm behind a cabinet back or across a joint that has opened.
  • 39 mm for a bed rail or a rack upright, where the long leg carries two screws.

Why The Width Is 16 mm

Bracket width decides the fit, and 16 mm still leaves room for a screw either side of the centreline.

  • The bracket sits inside a drawer side or on a cabinet back without overhanging.
  • A wider bracket in the same corner fouls the drawer box before the drawer closes.
  • The width is measured across the screw face, not along the leg.
G-JM21 size drawing with the four leg lengths, the 16 mm width and the 2 mm thickness

Stainless, And Where It Belongs

The bracket has no plating to chip, so it holds up in a kitchen, a bathroom cabinet or a utility rack.

  • Indoors and under cover outdoors both suit the bracket; standing water does not.
  • No grade is printed on the frames, so the steel grade is quoted on the order.
  • It looks the same in a year as on delivery, which a display fit-out needs.

One Hole Or Two

The three shorter bracket sizes carry one hole per leg, which locates a face but does not stop it turning.

  • The 39 mm size has two holes in its long leg, so a rail cannot swing.
  • Where both legs need two holes, a larger corner bracket in the range is the right part.
  • Two screws in one leg and one in the other is the usual repair.

Fitting It

Most bracket failures at this size are fitting failures, and they are avoidable.

  • Clamp the joint closed and flush before the bracket goes on.
  • Pilot every bracket hole, and keep the screws out of the centreline.
  • If the old holes are oval, move the bracket and drill fresh pilots.

The Limits

This is a light bracket and it is better sold as one than returned as something more.

  • The bracket will not carry the corner load of a broken rail or a loaded carcass.
  • If the member is much wider than the bracket, the ends go unsupported.
  • If the two faces are not at a right angle, no folded bracket will fit.
G-JM21 selling point panel, right angle fold and rounded tail with no scraping

Packing, Mixing And Names

The bracket is bought by the bag, and a mixed order of the four lengths is the normal one.

  • Each bracket length is counted and bagged separately, and the mix is listed line by line.
  • Screws are not included; say whether they should travel in the same carton.
  • Buyers ask for it as a stainless steel L bracket, a small corner brace, or a 2mm thick corner bracket.

G-JM21 is a stainless steel L bracket 16 mm wide and 2 mm thick, with 19, 24, 29 and 39 mm legs, rounded tails and one hole per leg.

State the leg lengths, the quantity of each and whether screws travel with them, and the bracket can be checked against the piece before anything is packed.

Who Makes The Bracket

G-JM21 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping and finishing in house, eighteen years of small hardware for importers and own-brand programmes.

The panels below are the plant and the paperwork behind every bracket on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Which size fits a drawer box?

The 19 mm one, because the strip has to clear the runner.

Are screws included?

No. The screw is chosen for the board, so say if you want them in the same carton.

Is it stainless or plated?

Stainless steel, so there is no plating to chip at the fold. The grade is quoted on the order.

Can I mix the four lengths?

Yes, and it is the usual order. Each length is counted and bagged separately.

Will it hold a shelf of books?

For a light shelf on sound timber, yes. For real weight, a heavier corner bracket in the range is the right part.