0
image
image
image
image
hidden drawer slides

Concealed Undermount Drawer Slide G-H630

G-H630
G-H630 is a concealed drawer slide rail with a perforated mounting plate that screws to the drawer box, so the runner sits under the drawer and stays out of sight, in steel and supplied in pairs.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The G-H630 Concealed Drawer Slide

The G-H630 is a concealed slide: the rail runs under the drawer box instead of along its side, so from the front of the cabinet there is nothing to see but the drawer. The perforated plate carries the fixing points and the runner slides inside it.

G-H630 concealed drawer slide rail pair with perforated mounting plates

At A Glance

ItemG-H630
MaterialSteel
TypeConcealed slide rail
MountingUnder the drawer box
FixingPerforated mounting plate
FinishBright steel
PackingPairs

How It Stays Hidden

A concealed slide is bought for what is not visible, and the geometry of this one keeps the whole runner under the drawer.

  • The drawer front hides the slide from anyone standing at the cabinet.
  • There is no side clearance to cut into the drawer box, so the box keeps its full internal width.
  • The visible part of the fitting is the drawer front itself, which is what a clean interior is judged on.

What The Mounting Plate Does

The perforated plate is the interface between the slide and the drawer box, and the hole pattern is what sets the fixing positions.

  • The plate spreads the load over the drawer bottom instead of pulling on two or three screws.
  • The holes accept a standard screw, so the fitter does not need a special fixing.
  • The runner travels in the plate, which is what keeps the drawer square as it comes out.
Close up of the G-H630 mounting plate and the runner beside it

Fitting It

A concealed slide is set out from the drawer box, not from the cabinet side, so the plate position is the first thing to get right.

  • Fix the plate to the drawer box first and check that the box sits square before the cabinet side is drilled.
  • Keep the screws loose until the drawer runs without rubbing, then tighten from the back forwards.
  • Check the drawer front gap across the whole width once the slide is loaded.

The Limits

This is a cabinet slide and it is sold as one.

  • No length and no load figure are printed on the frames, so both are quoted on the order rather than claimed here.
  • It is not a runner for a vehicle, a tool chest or an industrial rack.
  • A drawer that is stood in or climbed on needs a heavier slide.
The G-H630 plate seen from the fixing side

Ordering

The slide is matched to the drawer box, so the depth and the plate pattern are agreed on the order.

  • Give the drawer box depth and width with the enquiry, and the slide is matched to it.
  • Say how many pairs, because the two slides of a pair are packed together.
  • Screws are quoted with the order if they are wanted in the same carton.

What Buyers Call It

The same slide is asked for under several names, and any of them reaches this part.

  • Concealed drawer slides, which is what the trade calls a runner that sits out of sight.
  • Undermount drawer slides, when the position under the box is the point of the order.
  • Hidden drawer slides, which is the plain way the same part is described on a retail page.

The G-H630 is a concealed drawer slide rail with a perforated mounting plate, fitted under the drawer box.

State the drawer box depth and width, and the slide is checked before it is packed.

Who Makes The Slide

The G-H630 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every slide on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Will the slide be visible when the drawer is shut?

No. The rail sits under the drawer box, so the drawer front is what shows.

Does it fit a standard drawer box?

It is set out from the box rather than the cabinet side, so give the box depth and width with the enquiry and the slide is matched.

What are the holes on the plate for?

They are the fixing points for the drawer box, and they take a standard screw.

Are screws included?

No. Screws are quoted with the order if they are wanted in the same carton.

Is there a load rating?

The frames carry no load figure, so the rating is quoted on the order for the drawer it is going into.