0
image
image
image
image
stainless steel push to open drawer slides

G-HRB Stainless Steel Push Open Rebound Drawer Slide

G-HRB
G-HRB is the stainless rebound slide: press the drawer front, the spring in the end housing lets go and the drawer comes out on three sections, side mounted and supplied in pairs.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The G-HRB Stainless Rebound Slide

The G-HRB is a rebound slide that opens without a handle: the drawer is pressed in, the catch lets go, and the spring in the housing at the cabinet end pushes it out far enough to take hold. It is the slide for flat fronts, where a pull would break the line.

G-HRB stainless steel rebound drawer slides in pairs

At A Glance

ItemG-HRB
MaterialStainless steel
TypeThree section ball bearing slide
OpeningPush to open, rebound spring
ExtensionFull, drawer clear of the cabinet
MountingSide mount, cabinet member
HousingMoulded end piece at the cabinet end
PackingPairs

How The Rebound Works

The rebound sits in the housing at the cabinet end of the slide. The drawer front closes against it, the catch takes hold, and the spring stays loaded while the drawer is shut.

  • Press the front and the catch releases; the spring pushes the drawer out far enough to take hold.
  • Stainless steel push to open drawer slides need no pull at all, which suits a handle-free front.
  • The press face is the whole front, so a knee or an elbow works as well as a hand does.

Three Sections, Full Extension

Three sections give the slide two travelling members inside the body, so the drawer comes out past the cabinet face and the back of the box comes into reach.

  • Rebound slide rails are three member here, the travel a kitchen drawer is usually asked for.
  • Three section rebound drawer slides are the ones to quote where a deeper drawer would otherwise leave the back out of reach.
  • The members of the slide are pressed as one family, so the middle member lines up with the outer one.
The G-HRB pair, three section body with the rebound housing

The Stainless Body

The rails of the slide are stainless steel, so the surface that runs is the metal itself rather than a plated coat, and the edge of a fixing hole stays where it was cut.

  • That is the reason the slide is asked for in kitchens, bathrooms and anything washed down.
  • The housing is clipped onto the outer member, so it can be replaced without the pair coming off the cabinet.
  • The ball cages are the same in both members of the slide, so the travel feels the same throughout.

Fitting It

The slide is set like any side mount slide. The one extra is the press gap at the drawer front: it has to travel in before the catch lets go.

  • Set the cabinet square and mark the drawer line on both sides before the first screw goes in.
  • Fix the flange with the screws loose, set the box on the runners and let the slide find its line, then tighten from the back forwards.
  • Press the slide in and let it out three times before the drawer front is finally adjusted.
The G-HRB outer member with the rebound housing at the cabinet end

The Limits

This is a cabinet slide, and it is sold as one.

  • No length and no load figure for the slide are printed on the frames, so both are quoted on the order.
  • It is not a soft close slide: the spring opens the drawer and the catch takes the closing.
  • A drawer that is stood in or climbed on needs a heavier slide than this one.

Ordering

The slide is matched to the drawer, so the drawer depth and the length wanted are agreed before the pair is packed.

  • Give the drawer depth and the cabinet width with the enquiry, and the slide is matched to them.
  • Say how many pairs; the two hands are packed together and quoted as a pair.
  • Screws are quoted with the order if they are wanted in the same carton.

What Buyers Call It

The same slide is asked for under three names, and any of them reaches this one.

  • Stainless steel push to open drawer slides, when the finish and the opening are both in the enquiry.
  • Rebound slide rails, the name the part carries in the trade and on the carton.
  • Three section rebound drawer slides, when the travel is what the drawing sets out.

The G-HRB is a stainless steel rebound slide: three section, full extension, side mounted, opened by pressing the drawer front.

State the drawer depth and the length wanted, and the pair is checked before it is packed.

Who Makes The Slide

The G-HRB is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every slide on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Does the drawer stay shut on its own?

Yes. The catch holds the front closed and only lets go when the front is pressed in. A drawer that is slammed will still bounce, so the front is pushed rather than thrown.

Is there a damper as well?

No. The spring opens the drawer and the catch takes the closing; there is no damper. Where soft close is wanted on the same box, it is a different slide.

Does the drawer need a handle?

No. The front is the press face, so a handle-free front works and the run of fronts stays flat.

How far does it pull out?

Full extension. With three sections the drawer clears the cabinet face and the back of the box comes into reach.

Is there a load rating?

The frames carry no load figure, so the rating is quoted on the order for the drawer the slide is going into.