H630 Concealed Undermount Drawer Slide with Fittings
The H630 Concealed Undermount Slide
The H630 is the undermount slide with the deep body: the runner is boxed in on both sides, the flange is pierced in two rows, and the plastic fittings that hold the drawer box come in the pack rather than being ordered separately. Once the drawer is in, none of it shows.
At A Glance
| Item | H630 |
| Material | Steel, plated |
| Type | Concealed undermount slide |
| Mounting | Under the drawer box |
| Fixing | Perforated flange, two rows |
| In The Pack | Plastic end fittings and locking piece |
| Damper | None |
| Packing | Pairs |
The Deep Body
The body is a box section rather than an open channel, and that is what the frames show from every angle: two side walls, a flat face, and the runner travelling inside.
- A boxed body keeps the runner off the cabinet floor, so sawdust and crumbs do not get into the track.
- The walls carry the drawer weight across the length of the slide instead of through the flange alone.
- The body sits under the box, so the drawer side stays flat and the internal width is kept.
The Flange And Its Holes
The flange is pierced in two rows of oval holes, which is what lets the slide be set to the line the cabinet actually has.
- The oval holes allow the slide to be moved a little after the first screw is in, without re-drilling.
- Two rows mean the fixing can be taken high or low on the same flange.
- The flange is what screws to the cabinet, so the slide can come out again without disturbing the drawer box.
The Fittings In The Pack
The frames show the orange plastic pieces loose beside the slides, and the white nylon piece set into the rail end, because they are part of the pair as shipped.
- The plastic fittings are the interface between the slide and the drawer box, so they are supplied with the slide rather than guessed at on site.
- The white nylon piece at the rail end is the part the box seats against.
- Keeping the fittings with the pair is what makes a replacement slide a straight swap.
Fitting It
An undermount slide is set from underneath, so the cabinet bottom and the drawer line have to be right before the first screw goes in.
- Mark the drawer line on both cabinet sides and check it against the box before drilling.
- Fix the flange with the screws loose, set the box on the fittings and slide it until it runs, then tighten from the back forwards.
- Pull the drawer out and push it back twice before sign off, and check the fittings stay seated.
The Limits
This is a cabinet slide and it is sold as one.
- No length and no load figure are printed on the frames, so both are quoted on the order.
- There is no damper in this slide; where a soft close is wanted, the buffered slide in the range is the part to order.
- A drawer that is stood in or climbed on needs a heavier slide than this one.
Ordering
The slide is matched to the drawer box, so the box depth and the length wanted are agreed before the pair is packed.
- Give the drawer box depth and the cabinet width with the enquiry, and the slide is matched to it.
- Say how many pairs; the fittings are packed in the same carton as the pair.
- Screws are quoted with the order if they are wanted in the same carton.
What Buyers Call It
The same part is asked for under three names, and any of them reaches this slide.
- Undermount drawer runners, which is how the part is listed on European trade pages.
- Zinc plated drawer slides, when the finish is how the order is specified.
- Concealed undermount drawer slides, which is the full name on a US cabinet hardware page.
The H630 is a concealed undermount drawer slide with a deep plated body, a two row perforated flange and its plastic fittings in the pack.
State the drawer box depth and the length wanted, and the pair is checked before it is packed.
Who Makes The Slide
The H630 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.
The panels below are the plant and the paperwork behind every slide on this page.
Eighty Countries, Six Numbers
Three Production Bases
The Certificates, And What Each One Covers
Headquarters, Showrooms And Design
Where To Meet Us, March To December
Four Carton Options, And The Delivery Window
OEM, Brochures And Display
Frequently Asked Questions
Do the plastic fittings come with it?
Yes. The orange end fittings and the white nylon rail piece are packed with the pair, because they are what the drawer box seats on.
Is any of it visible?
No. The slide runs under the drawer box, so the drawer side is flat and nothing shows at the front.
Does it close softly?
No. There is no damper in this slide. The buffered slide in the range fits the same drawer box.
Are screws included?
No. Screws are quoted with the order if they are wanted in the same carton.
Is there a load rating?
The frames carry no load figure, so the rating is quoted on the order for the drawer the slide is going into.
Comprehensive score