Full Extension Ball Bearing Drawer Slide H200
The H200 Three Section Ball Bearing Slide
The H200 is the plain one in the range: a three section slide on a cage of steel balls, pulling out until the drawer is clear of the cabinet. There is no damper in it, so the drawer closes the way the hand pushes it.
At A Glance
| Item | H200 |
| Material | Steel, plated |
| Type | Three section ball bearing slide |
| Mounting | Side mount |
| Extension | Full, drawer clear of the cabinet |
| Damper | None |
| Release | Plastic lever on the inner rail |
| Packing | Pairs |
The Ball Cage
The slide rolls rather than rubs, because a cage of steel balls runs between the sections and takes the drawer weight along the whole travel of the slide.
- The balls are the wear part, so a slide that is stiff on the bench is usually a cage knocked out of line.
- The cage keeps the sections apart, which is why the slide stays free at full extension instead of dragging at the outer end.
- A loaded drawer should pull with two fingers from the first inch to the last.
Three Sections, Full Extension
Three sections means two travelling members inside the cabinet member, so the drawer comes out past the cabinet face and the back of the box is reachable.
- Full extension ball bearing drawer slides put the whole drawer in reach, which matters on a deep cabinet where the back third is otherwise lost.
- The sections are stamped as one family, so the middle member lines up with the outer one.
- The lever at the inner end releases the drawer, so a finished carcass can be moved with the drawers out.
Side Mount
The body screws flat against the cabinet side and the drawer side, the fixing most cabinet shops already have jigs for.
- The flange is pierced along its length, so the slide can be positioned rather than drilled where it happens to sit.
- Left and right slides of a pair are handed, and the pair is packed together.
- Nothing hangs below the drawer, so the box keeps its depth.
No Damper, By Choice
This slide has no buffer in it, so nothing has to be adjusted and nothing pulls the drawer shut on its own.
- On a utility drawer a plain slide is quicker to fit and cannot be blamed for a drawer that will not stay put.
- Where a soft close is wanted, a buffered slide is the part to order, not a damper added to this one.
- The travel is the same as the buffered slide in the range, so the drawer box does not change.
Fitting It
A cabinet drawer slide is only as good as the square of the carcass, so the order of work matters.
- Set the cabinet side square, then fix the cabinet member along the drawer line.
- Fix the drawer member with the screws loose, close the drawer, and let the slide find its own line before tightening from the back forwards.
- Pull the drawer to full extension and check the lever releases before sign off.
The Limits
This is a cabinet slide and it is sold as one.
- No length and no load figure are printed on the frames, so both are quoted on the order.
- A drawer that is stood in or climbed on needs a heavier slide than this one.
- The finish is plated steel or black; where it has to match, say so on the order.
Ordering
The slide is matched to the drawer box, so the box depth and the length wanted are agreed before the pair is packed.
- Give the drawer box depth and the cabinet width with the enquiry, and the slide is matched to it.
- Say how many pairs, because the two hands are packed together.
- Screws are quoted with the order if they are wanted in the same carton.
What Buyers Call It
The same part is asked for under three names, and any of them reaches this slide.
- Ball bearing drawer slides, which is the name on most of the trade pages this part is compared with.
- Full extension ball bearing drawer slides, when the travel is the point of the order.
- Cabinet drawer slides, which is how a kitchen or furniture buyer asks for the pair.
The H200 is a three section ball bearing drawer slide with full extension, side mount and no damper.
State the drawer box depth and the length wanted, and the pair is checked before it is packed.
Who Makes The Slide
The H200 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.
The panels below are the plant and the paperwork behind every slide on this page.
Eighty Countries, Six Numbers
Three Production Bases
The Certificates, And What Each One Covers
Headquarters, Showrooms And Design
Where To Meet Us, March To December
Four Carton Options, And The Delivery Window
OEM, Brochures And Display
Frequently Asked Questions
Does the drawer come right out?
Yes. The lever at the inner end releases the drawer from the slide, so the box lifts off and goes back on the same way.
Is there a soft close on it?
No. This slide has no damper, so the drawer closes as it is pushed. The buffered slide in the range fits the same drawer box.
Which finish does it come in?
The frames show plated steel and black. Both are steel, and the finish is fixed on the order.
Are screws included?
No. Screws are quoted with the order if they are wanted in the same carton.
Is there a load rating?
The frames carry no load figure, so the rating is quoted on the order for the drawer the slide is going into.
Comprehensive score