G-KB01 Under Desk Keyboard Slide With Brackets
The G-KB01 Under Desk Keyboard Slide
The G-KB01 is a keyboard slide rather than a drawer slide: the same ball bearing pair, but fitted with mounting brackets that screw to the underside of a desk, so a keyboard shelf travels out under the hands and pushes back out of the way.
At A Glance
| Item | G-KB01 |
| Material | Cold rolled steel |
| Type | Ball bearing keyboard slide |
| Mounting | Under desk, brackets supplied |
| Travel | Full extension |
| Finishes | Zinc, black |
| Supplied with | Brackets and screws, in pairs |
A Slide Built For A Keyboard
The slide carries a platform instead of a drawer front, so the brackets sit on the flat underside of the desk and the tray hangs from them. That is the whole difference between this slide and the pedestal slide beside it in the catalogue.
- The pair is fixed to the underside of the desk, not to the sides of a cabinet, so no carcass is needed.
- A platform, a shelf or a shallow tray is screwed to the moving side of the slide.
- Nothing presses against a drawer front, so the platform can come off and go back without touching the desk.
The Brackets
Two brackets per side are the part that makes a keyboard slide fit a desk: they turn the flat underside of the desk into a mounting face for the slide.
- The brackets are slotted, so the height of the platform is set after the slide is on the desk rather than before.
- Slots also let the keyboard slide be squared up when the desk edge is not straight.
- They are packed with the pair, so no separate carrier has to be found for the keyboard slide.
Ball Bearing Travel
The ball cages run the length of the slide, so a loaded platform moves without the judder a plain channel gives once it is part extended.
- The travel is full extension, so the keyboard comes clear of the desk edge instead of stopping short.
- The balls sit in a cage, which keeps a wide tray level at the far end.
Two Finishes
The pair is made in zinc and in black, and the two are used for different reasons rather than as a preference.
- Zinc is the plain finish, used where the slide is seen against a light desk frame.
- Black is the one that disappears against a dark underframe.
Fitting It Under A Desk
The order of work matters more than the tools: the keyboard slide is set out on the desk before anything is screwed to it.
- Mark the two bracket lines on the underside before drilling.
- Fix the brackets to the desk first, then set the slide on them, so the slide is not held while it is levelled.
- Check the platform clears the desk edge through the travel before the screws go down.
Where It Goes
This is the slide for a working surface that has no pedestal: a home office desk, a counter, a bench.
- Home office and studio desks where the keyboard has to leave the worktop clear.
- Reception counters and workshop benches, where a drawer would foul the user's knees.
- A desk with a shelf under it; it is not a slide for a drawer that is stood in.
Ordering
Length and finish are what the order is built from, and both are chosen against the desk. No load figure is printed on the frames, so the rating is quoted with the order.
- Give the width under the desk and the depth of the platform the slide carries.
- Say how many pairs and which finish, zinc or black.
What Buyers Call It
Three names reach this part, and each of them describes a different side of it.
- A buyer replacing the runner under a keyboard shelf asks for a keyboard slide and nothing more.
- The fitter working from the underside of the desk calls the same part an under desk keyboard slide.
- A counter with no pedestal takes it as a keyboard drawer slide, because the platform is a drawer.
The G-KB01 is a ball bearing keyboard slide in pairs, supplied with the brackets and screws that fix it under a desk.
State the width under the desk, the platform it carries and the finish, and the pairs are made and packed.
Who Makes The Slide
The G-KB01 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, with stamping, ball assembly and finishing in house.
The panels below are the plant and the paperwork behind every keyboard slide on this page.
Eighty Countries, Six Numbers
Three Production Bases
The Certificates, And What Each One Covers
Headquarters, Showrooms And Design
Where To Meet Us, March To December
Four Carton Options, And The Delivery Window
OEM, Brochures And Display
Frequently Asked Questions
Do the brackets come with the slide?
Yes. Two brackets per side and the screws are packed with the pair, so nothing else has to be ordered to fit it.
Can it go on a cabinet instead of a desk?
It can, but the brackets are shaped for a flat underside. On a cabinet the ordinary side mount slide is the part for the job.
How much will it hold?
No load figure is printed on the frames, so the rating is quoted on the order against the platform the keyboard slide carries.
Is one side enough for a shelf?
No. The pair is the unit of sale, because a platform needs a keyboard slide on each side to stay level.
Can the height be set after fitting?
Yes. The brackets are slotted, so the platform is levelled on the keyboard slide after it is on the desk.
Comprehensive score