H310-45 Push Open Three Section Drawer Slide
The H310-45 Push Open Three Section Drawer Slide
The H310-45 is the wide version of the rebound slide: a black ball bearing runner with a spring latch in the middle section, built on a 45 mm section, so a pan drawer or a wide base unit still opens on a press.
At A Glance
| Item | H310-45 |
| Material | Cold rolled steel |
| Type | Three section ball bearing slide |
| Section | 45 mm high |
| Function | Spring rebound, press to open |
| Mounting | Side mount, pairs |
| Colours | Black, zinc |
Press To Open
The latch sits in the middle section of the slide and holds the drawer shut on a spring. Push the front and the spring releases the catch, so the drawer travels out far enough on the slide to take hold of.
- A handleless drawer front only needs a push on the face, which is what a plain kitchen run asks for.
- The spring is set in a housing, so the latch does not rub on the ball cage.
- Push the drawer home and the same spring pulls the slide the last part of the way in, so it cannot be left ajar.
Why Three Sections
Three sections mean the drawer comes out over its whole length, so the back of a deep drawer is reachable rather than lost behind the front two thirds.
- Each section carries its own ball cage, so the load is spread along the slide rather than taken at one point.
- The middle section is the one holding the latch, which keeps the mechanism out of the fixing area.
- Full travel also means the drawer can be lifted out once the two are separated.
The 45 Mm Section
The section height is the number to match when a drawer is being replaced. This one prints 45 mm on the drawing, which is the taller section, used where a smaller section looks light on a wide front.
- A taller section resists twisting on a wide drawer, which is where a shallow slide starts to bind.
- The same height gives more room for the ball cage, so the slide stays smooth under a pan load.
- Check the drawer side and the carcass clearance before ordering, because the slide needs the space.
Fitting The Slide
The slide pair is fitted level on the two sides of the drawer, and the front is set on the slide rather than on the carcass.
- Release the latch on the slide by hand before the drawer goes in, so the front can be lined up with the drawer shut.
- Keep the mounting screws in the slotted holes of the slide so the front can be moved after the first fit.
- Leave the drawer out until both slides run without a catch, then fit the front.
Where It Goes
This is a kitchen and furniture slide, used where a drawer front is plain and the opening is wide.
- Handleless kitchen runs, where a push is easier than a pull.
- Wide base units and pan drawers that need a stiff slide.
- Not a slide for a drawer that is stood in or climbed on; a heavier system is the part for those.
The Limits
Nothing printed on the frames is a load rating, so the figure comes from the order.
- A load figure is not printed on the frames, so it is quoted against the drawer the slide goes into.
- The finish is a colour, not a corrosion grade; a steel grade is quoted on request.
- The rebound spring is set for a drawer front within a normal furniture weight; a heavy front changes the feel.
Ordering
The slide length is chosen against the drawer depth, so the depth is given with the enquiry.
- Give the drawer depth, the drawer width and the section height of the old slide, and the length follows.
- Say how many pairs and which colour.
- Screws are quoted with the order if they are wanted in the same carton.
What Buyers Call It
The same slide is asked for under three names, and any of them reaches this part.
- 45mm drawer slide, when the section height is the first thing matched against the old slide.
- Push open drawer slide, when the kitchen is handleless and the front has to respond to a press.
- Three section drawer slide, when the drawer has to come out over its full length.
The H310-45 is a black three section ball bearing slide with a spring rebound latch and a 45 mm section, sold in pairs.
State the drawer depth, the drawer width and the section height, and the pairs are made and packed.
Who Makes The Slide
The H310-45 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.
The panels below are the plant and the paperwork behind every slide on this page.
Eighty Countries, Six Numbers
Three Production Bases
The Certificates, And What Each One Covers
Headquarters, Showrooms And Design
Where To Meet Us, March To December
Four Carton Options, And The Delivery Window
OEM, Brochures And Display
Frequently Asked Questions
Does it need a handle?
No. The latch releases on a push, so a plain front works without a handle or a groove.
What does the 45 in the model mean?
The section height printed on the drawing, 45 mm. It is the number to match when an old slide is being replaced.
Will it hold a pan drawer?
No load figure is printed on the frames, so the rating is quoted on the order for the drawer the slide goes into.
Does the drawer come right out?
It travels the full length on three sections and can be lifted off once the two parts are separated.
Is one side supplied on its own?
No. The pair is the unit of sale, because a drawer needs a runner on each side.
Comprehensive score