0
image
image
image
image
drawer box and runners

H500 Metal Sided Drawer Box And Runners

H500
H500 is a metal sided drawer box with its runners: steel sides, a panel bottom and clipped front connectors go together on the bench, and the drawer runs on a ball bearing runner in the same set.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The H500 Drawer Box And Runners

The H500 is a drawer box and its runners in one set. The sides are steel, the bottom is a panel, and the front is held by a clip on each side, so a drawer is assembled from parts and set on the runner rather than built out of timber.

H500 metal sided drawer box with its runners

At A Glance

ItemH500
MaterialSteel sides, panel bottom
TypeMetal sided drawer box
RunnersBall bearing, in the set
FrontClipped connector each side
ColoursWhite, grey
PackingSets

A Box And Its Runners

A metal sided drawer box is only half a drawer until the runner is on the cabinet. The H500 is quoted with its runner, so the drawing that goes to the bench is the drawer and the travel together.

  • The runner carries the drawer on steel balls, so a loaded drawer starts and stops without the shove a roller slide needs.
  • The box is set on the runner after the cabinet is squared, which is the order a fitter works in.
  • The runner length follows the cabinet depth, so the depth is what the order is built on.

The Front Clips

Each side carries a clip that takes the drawer front, and the clip is what gives the front its adjustment once the drawer is in the cabinet.

  • The front goes on after the box is on its runners, so the gap can be set against the carcass rather than against the bench.
  • A clip on each side is released to take the front off again, which is how a finished run is touched up or replaced.
  • Both sides use the same clip, so a spare is one part number.
The H500 sides, bottom panel and front clips

Putting A Drawer Together

The box goes together on the bench, square, and the front is the last thing that goes on.

  • Stand the sides on their bottom edge, set the panel between them, and check the diagonals before the last screws are driven.
  • Set the box on the runners, run it in and out twice, and only then fit the front.
  • Sit the front on the clips, set the gap with the drawer shut, and tighten.
The H500 drawer closed on its runners

Where It Goes

This is a kitchen and furniture drawer, and it is sold as a set of parts with the runner.

  • The steel side wipes out, which is what a kitchen drawer needs at the front of the run.
  • A drawer that is stood in or climbed on needs a heavier system than this one.
  • A cutlery insert is not part of the set; it is quoted separately when it is wanted.

The Limits

Nothing on the frames is a specification, so the numbers come from the order.

  • No length, no height and no load figure are printed on the frames, so all three are quoted against the cabinet opening.
  • The finish is a colour, not a steel grade; a grade is quoted on request.
  • The runner is quoted with the box, so a box on its own is not a complete drawer.

Ordering

The set is built to the opening, so the cabinet width, the drawer depth and the height are agreed first.

  • Give the cabinet opening, the drawer depth and the height wanted with the enquiry.
  • Say how many drawers and which of the two colours.
  • Screws and the cutlery insert are quoted with the order when they are wanted in the same carton.

What Buyers Call It

The same set is asked for under three names, and any of them reaches this drawer box.

  • Metal sided drawer box, when the material of the side is what the drawing calls out.
  • Drawer box and runners, when the runner has to come with the box in one order.
  • Tandem box drawer, the trade name for a metal box with its runner built into the side.

The H500 is a metal sided drawer box supplied with its ball bearing runners, in white or grey, with a clipped front connector each side.

State the cabinet opening, the drawer depth and the height, and the sets are made and packed.

Who Makes The Box

The H500 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every drawer on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Is the runner in the price?

The set is quoted with its runner, because a box without a runner is not a drawer. The runner length follows the cabinet depth.

Can the front be adjusted after fitting?

Yes. The front sits on a clip on each side, so it can be moved and set again with the drawer in place.

Which height should be ordered?

The height that suits the opening. No height is printed on the frames, so it is quoted against the cabinet.

Does it take a cutlery insert?

An insert can sit inside it, and it is quoted separately. It is not part of the set.

What load does it carry?

The frames carry no load figure, so the rating is quoted on the order for the drawer the set is going into.