0
image
image
image
image
3d adjustable drawer box

H510 Metal Drawer Box System

H510
H510 is a metal drawer box system: two steel sides with moulded end caps, a bottom panel and a clipped front connector, put together on the bench and set on its runners in white or grey.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The H510 Metal Drawer Box

The H510 is the middle box of the metal drawer family, and it is supplied as parts: two steel sides, a panel bottom and a front connector that clips on. The end of each side is closed with a moulded cap, so the drawer has no cut edge on show.

H510 metal drawer box shown as parts and assembled

At A Glance

ItemH510
MaterialSteel sides, panel bottom
TypeMetal drawer box system
EndsMoulded cap on each side
FrontClipped connector each side
ColoursWhite, grey
PackingSets

The Moulded Ends

The cap on the end of each side is the part that makes a steel drawer safe to handle: it covers the folded end and it carries the fixing for the front connector.

  • The cap is a push fit on the side, so a damaged one is replaced without the drawer coming apart.
  • Because the cap closes the end, the inside of the drawer is a plain steel face with no pocket to trap crumbs.
  • Both caps are the same part, so a spare is one number.

A Box On Runners

A metal drawer box system is only a drawer once the runner is under it, and the runner is quoted with the set so the bench gets the drawer and the travel together.

  • The 3d adjustable drawer box front is set on the bench and then trimmed in the cabinet, which is the order a fitter works in.
  • The box is lifted onto the runners after the cabinet is squared, and the drawer is run in and out before the front goes on.
  • The runner length follows the cabinet depth, so the depth is what the order is built on.
The H510 sides with their moulded end caps

Putting A Drawer Together

The box goes together square on the bench, and the front is the last thing that goes on.

  • Stand the sides on their bottom edge, set the panel between them, and check both diagonals before the last screws are driven.
  • Clip the connector on, sit the box on its runners and run it twice.
  • Fit the front last, with the drawer shut, so the gap is set against the carcass.
The H510 drawer closed on its runners

Where It Goes

This is a kitchen and furniture drawer, sold as a set of parts with its runner.

  • A steel side wipes out, which is what a kitchen drawer needs at the front of a run.
  • A drawer that is stood in or climbed on needs a heavier system than this one.
  • A cutlery insert is not part of the set and is quoted separately.

The Limits

Nothing printed on the frames is a specification, so the numbers come from the order.

  • No length, no height and no load figure appear on the frames, so all three are quoted against the cabinet opening.
  • The colour is a finish, not a steel grade; a grade is quoted on request.
  • The runner comes with the box, so a box on its own is not a complete drawer.

Ordering

The set is built to the opening, so the cabinet width, the drawer depth and the height are agreed first.

  • Give the cabinet opening, the drawer depth and the height wanted with the enquiry.
  • Say how many drawers and which of the two colours.
  • Screws and the insert are quoted with the order when they are wanted in the same carton.

What Buyers Call It

The same set is asked for under three names, and any of them reaches this drawer.

  • Metal drawer box system, when the whole drawer and its runner are being specified together.
  • 3d adjustable drawer box, when the front has to be trimmed in two directions after fitting.
  • Kitchen drawer box, when the drawer is going into a run of kitchen units.

The H510 is a metal drawer box system with moulded end caps, a panel bottom and a clipped front connector, in white or grey, with its runner.

State the cabinet opening, the drawer depth and the height, and the sets are made and packed.

Who Makes The Box

The H510 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every drawer on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Does the runner come with it?

Yes. The set is quoted with its runner, because a box without a runner is not a drawer. The length follows the cabinet depth.

What does 3d adjustable mean here?

The front sits on a connector that can be trimmed after the drawer is in the cabinet, so the gap is set on the finished run rather than on the bench.

Can a damaged end cap be replaced?

Yes. The cap is a push fit on the side, so it comes off and goes back on without taking the drawer apart.

Which height should be ordered?

The one that suits the opening. No height is printed on the frames, so it is quoted against the cabinet.

What load does it carry?

The frames carry no load figure, so the rating is quoted on the order for the drawer the set is going into.