0
image
image
image
image
metal drawer box system

H520 High Metal Drawer Box

H520
H520 is the deep box of the metal drawer family: tall steel sides with moulded end caps over a panel bottom, a clipped front connector, and two runners with the set.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The H520 High Drawer Box

The H520 is the deep box of the family. The sides are taller than the low box, so a pan or a stack of plates sits inside without fouling the cabinet, and the end of each side is closed with a moulded cap.

H520 high metal drawer box shown with its runners

At A Glance

ItemH520
MaterialSteel sides, panel bottom
TypeHigh metal drawer box
EndsMoulded cap on each side
FrontClipped connector each side
RunnersTwo, in the set
ColoursWhite, grey
PackingSets

A Deep Box

A deep drawer box is what a pan cupboard needs: the drawer is deep enough The side runs the full height of the drawer, so a tall load is carried by the side rather than piled above it.

  • The drawer takes a pan upright, which is the reason this height exists.
  • The sides are steel, so the inside wipes out and nothing soaks in.
  • The bottom panel is cut to the cabinet opening, so the box is made to the carcass rather than to a nominal size.

The Moulded Ends

The cap at each end closes the folded steel, so the drawer has no cut edge on show and the front connector has something solid to sit on.

  • The cap is a push fit, so a damaged one is replaced without the drawer coming apart.
  • Both caps are the same part, so a spare is one number.
  • The connector clips onto the cap and the side, and the front is set on it last.
The H520 deep sides and their moulded end caps

Two Runners In The Set

The set is quoted with two runners, because a deep drawer is a loaded drawer and it runs on both sides of the cabinet.

  • The runners are set on the cabinet before the box goes in, and the box is then dropped on.
  • Runner length follows the cabinet depth, so the depth is the measurement the order is built on.
  • A drawer box on its own is not a complete drawer, which is why the runners travel with it.
The H520 box with its two runners

Fitting It

The drawer goes together square on the bench and the front is fitted in the cabinet, with the drawer shut.

  • Stand the sides on their bottom edge, set the panel between them, and check both diagonals before the last screws are driven.
  • Set the runners level and parallel, then drop the box on and run it in and out twice.
  • Fit the front last so the gap is set against the carcass rather than against the bench.

The Limits

Nothing printed on the frames is a specification, so the numbers come from the order.

  • No length, no height and no load figure appear on the frames, so all three are quoted against the cabinet opening.
  • The colour is a finish, not a steel grade; a grade is quoted on request.
  • A drawer that is stood in or climbed on needs a heavier system than this one.

Ordering

The set is built to the opening, so the cabinet width, the drawer depth and the height are agreed first.

  • Give the cabinet opening, the drawer depth and the height wanted with the enquiry.
  • Say how many drawers and which of the two colours.
  • Screws and an insert are quoted with the order when they are wanted in the same carton.

What Buyers Call It

The same set is asked for under three names, and any of them reaches this drawer.

  • Metal drawer box system, when the box and its runners are being specified together.
  • Drawer box and runners, when the runner has to come in the same order as the box.
  • Kitchen drawer box, when the drawer is going into a run of kitchen units.

The H520 is a high metal drawer box with moulded end caps, a panel bottom, a clipped front connector and two runners, in white or grey.

State the cabinet opening, the drawer depth and the height, and the sets are made and packed.

Who Makes The Box

The H520 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every drawer on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

How many runners come with it?

Two. A deep drawer runs on both sides of the cabinet, and the runners are quoted in the same set.

Is this the tallest box in the range?

No height is printed on the frames, so the height is quoted against the cabinet opening rather than picked from a chart.

Can a pan sit inside it?

The side runs the full height of the drawer, so a pan stands upright inside it without sitting above the side.

Can a damaged end cap be replaced?

Yes. The cap is a push fit on the side and comes off without taking the drawer apart.

What load does it carry?

The frames carry no load figure, so the rating is quoted on the order for the drawer the set is going into.