0
image
image
image
image
metal drawer box

H530 Square Rail Drawer Box

H530
H530 is the square rail drawer box: a steel side with a square section rail along its top edge, a panel bottom, a clipped front connector and a runner in the set.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The H530 Square Rail Drawer Box

The H530 is the square rail box of the family. The side is a folded steel profile with a square section rail running along its top edge, which is what gives the drawer its stiffness without a timber side.

H530 square rail drawer box side pack with its brackets

At A Glance

ItemH530
MaterialSteel sides, panel bottom
TypeSquare rail drawer box
DepthsLow, mid, high side
FrontClipped connector each side
ColoursGrey, white
PackingSets

The Square Section Rail

The rail is the reason the side stays straight. It is a closed square profile rather than an open fold, so the drawer keeps its shape when the load sits at one end.

  • The rail runs the full length of the side and closes the top edge, so nothing sharp faces the hand.
  • A closed profile resists twisting, which is what a wide drawer does when it is pulled from one corner.
  • Because the rail carries the stiffness, the side wall itself stays thin and the drawer keeps its width.

Three Depths, One Front

The low, mid and high side share the same front connector and the same runner, so a run can mix a shallow utensil drawer and a deep pan drawer.

  • The low side suits a cutlery or utensil drawer near the top of a base unit.
  • The high side holds bottles and pans, where the load sits against the side.
  • The mid side is the one used when the fronts have to read even across a run.
The H530 rails with their brackets and end caps

Assembling The Box

The drawer is assembled on the bench, and the front is fitted last with the drawer shut in its opening.

  • Set the panel between the two sides and check both diagonals before the last screws go in.
  • Clip the front connector to the side and drop the box onto its runner.
  • Fit the front against the carcass so the gap is measured on the cabinet, not on the bench.
The H530 sides seen from the front edge

Where It Goes

This is a kitchen and furniture drawer, supplied as a set of parts with its runner.

  • A steel side wipes out and does not swell, which is what a sink run asks for.
  • A drawer that is stood in or climbed on needs a heavier system than this one.
  • An insert or a cutlery tray is quoted separately and is not part of the set.

The Limits

Nothing printed on the frames is a specification, so the figures come from the order.

  • No length, no side height and no load figure appear on the frames; all three follow the cabinet opening.
  • The colour is a finish, not a steel grade; a grade is quoted on request.
  • The runner comes with the box, so a box on its own is not a complete drawer.

Ordering

The set is built to the opening, so the cabinet width, the drawer depth and the side depth are agreed first.

  • Give the cabinet opening, the drawer depth and which of the three sides with the enquiry.
  • Say how many drawers and which colour.
  • Screws and an insert are quoted with the order if they are wanted in the same carton.

What Buyers Call It

The same box is asked for under three names, and any of them reaches this drawer.

  • Square rail drawer box, when the rail profile is the reason for the enquiry.
  • Metal drawer box, when the material of the side is what the drawing calls out.
  • Drawer box and runners, when the whole set is bought rather than the box on its own.

The H530 is a square rail drawer box in a low, mid or high side, with a panel bottom, a clipped front connector and its runner.

State the cabinet opening, the drawer depth and the side depth, and the sets are made and packed.

Who Makes The Box

The H530 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every drawer on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Can the three depths be mixed in one kitchen?

Yes. The low, mid and high side take the same front connector and the same runner, so one run can carry a shallow and a deep drawer.

What does the square rail do?

It closes the top edge of the side as a closed profile, which is what keeps a wide drawer from twisting when it is pulled from one corner.

Is a runner included?

The set is quoted with its runner, because the runner length follows the cabinet depth.

Will a cutlery tray fit inside?

An insert can sit inside the box and is quoted separately. It is not part of the set.

What load does it carry?

The frames carry no load figure, so the rating is quoted on the order for the drawer the set is going into.