H542 Ultra Thin Metal Drawer Box System
The H542 Ultra Thin Drawer Box
The H542 is a drawer box supplied as parts: two steel sides, a bottom panel and a front connector that clips on without a screw. The sides are thin, so the box gives away less of the opening than a wooden drawer does.
At A Glance
| Item | H542 |
| Material | Steel sides, panel bottom |
| Type | Ultra thin drawer box system |
| Front | Clipped connector, no handle needed |
| Colours | Matt white, dark grey |
| Assembly | Flat parts, screwed and clipped |
| Packing | Sets |
What Comes In A Set
A set is the two sides of the drawer, the bottom panel that ties them together, and the connector that holds the front. The runner the drawer rides on is quoted with the set.
- The sides are handed, so a pair is what makes one drawer.
- The bottom panel is cut to the width of the cabinet opening, which is why the box is ordered by the opening rather than by a nominal size.
- The connector clips onto the side without a screw, so a front can be set and reset while the drawer is on the bench.
The Thin Side
A thin steel side is the point of the system. The wall of the drawer takes up less of the opening than a timber side does, and the inside of the drawer is a plain steel face that wipes out.
- Slim drawer box systems are asked for where the opening is fixed and the storage inside it has to be as wide as the cabinet allows.
- The side is pressed and folded, so the edge that meets the hand is a fold rather than a cut.
- A metal drawer box does not swell or delaminate in a wet kitchen, which is the second reason the system is specified.
Two Colours
The box is finished in matt white or dark grey, and the two are picked against the cabinet interior rather than against the front.
- Matt white disappears into a pale carcass; dark grey reads as a drawer when the front is open.
- The front connector is the same colour family as the side, so the join does not show a patch.
- Both colours are quoted at the same price line, so a mixed run is one order.
Putting A Drawer Together
The box goes together on the bench before it goes near the cabinet, and the front is fitted last.
- Stand the two sides on their bottom edge, set the panel between them and fix it square, then check the diagonals before the last screws are driven.
- Clip the connector onto both sides, offer the front up and set it flush before the adjustment is touched.
- Set the finished drawer on its runners, run it in and out twice, and only then set the front gap.
The Limits
This is a cabinet drawer box, and it is sold as a set of parts.
- No length and no load figure are printed on the frames, so both are quoted on the order against the cabinet opening.
- A drawer that is stood in or climbed on needs a heavier system than this one.
- A handle is not part of the set: the front is drilled for whatever pull the kitchen is using.
Ordering
The box is made to the opening, so the cabinet width and the drawer depth are agreed before the sets are packed.
- Give the cabinet opening width and the drawer depth with the enquiry, and the panel is cut to them.
- Say how many drawers and which of the two colours; the parts are packed together and quoted as a set.
- Screws and the runner are quoted with the order when they are wanted in the same carton.
What Buyers Call It
The same system is asked for under three names, and any of them reaches this drawer box.
- Slim drawer box system, when the wall thickness is the reason for the enquiry.
- Metal drawer box, when the material is what the drawing calls out.
- Kitchen drawer box, when the drawer is going into a run of kitchen units.
The H542 is an ultra thin metal drawer box system in matt white or dark grey, assembled from two sides, a bottom panel and a clipped front connector.
State the cabinet opening width, the drawer depth and the number of drawers, and the sets are cut and packed.
Who Makes The Box
The H542 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.
The panels below are the plant and the paperwork behind every drawer on this page.
Eighty Countries, Six Numbers
Three Production Bases
The Certificates, And What Each One Covers
Headquarters, Showrooms And Design
Where To Meet Us, March To December
Four Carton Options, And The Delivery Window
OEM, Brochures And Display
Frequently Asked Questions
Is a runner included?
Not in the box set. The runner the drawer rides on is quoted with the order, because the length depends on the cabinet depth.
Can the front be taken off again?
Yes. The connector clips on, so the front can be released and set again without the drawer coming out of the cabinet.
Which colour should be ordered?
Matt white for a pale carcass and dark grey where the open drawer should read as a drawer. Both are the same price line.
Does it hold a heavy load?
The frames carry no load figure, so the load is quoted on the order against the drawer the system is going into.
Is the bottom panel cut to size?
Yes. It is cut to the cabinet opening, so that measurement is what the order is built on.
Comprehensive score