0
image
image
image
image
drawer box and runners

H550 Ultra Thin Drawer Box

H550
H550 is the ultra thin drawer box: a slim steel wall in a low, mid or high side, a panel bottom and a clipped front connector, so the drawer takes the opening rather than the timber.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The H550 Ultra Thin Drawer Box

The H550 is the ultra thin box of the family. The wall is a slim steel side rather than a timber one, so the drawer takes almost the whole opening, and the side comes in a low, a mid and a high depth for the same carcass.

H550 ultra thin drawer box shown in its side depths

At A Glance

ItemH550
MaterialSteel sides, panel bottom
TypeUltra thin drawer box
DepthsLow, mid, high side
FrontClipped connector each side
ColoursGrey, white
PackingSets

Why Thin

A thin wall is the whole point. Ten millimetres of timber side is ten millimetres the drawer cannot use, and in a narrow cabinet that is the difference between a usable drawer and a shelf.

  • The side is pressed from steel sheet, so the wall is a fold rather than a board.
  • The inside face is plain, which means nothing catches when the drawer is loaded to the sides.
  • The same wall is used for all three depths, so a mixed run is one part family.

Three Depths, One Carcass

The low, mid and high side take the same front and the same runner, so a run can mix a shallow cutlery drawer and a deep pan drawer without a second system.

  • The low side suits a cutlery or utensil drawer near the top of a base unit.
  • The high side suits a pan or a bottle drawer, where the load has to be held by the side.
  • The mid side is the one specified when the run has to look even from the front.
The H550 side in its mid depth with the front connector

Putting A Drawer Together

The box is assembled on the bench and the front is set in the cabinet, with the drawer shut.

  • Set the panel between the two sides and check the diagonals before the last screws go in.
  • Clip the front connector on and set the box on its runner before the front is offered up.
  • Fit the front last so the gap is measured against the carcass.
The H550 box closed, ready for its front

Where It Goes

This is a kitchen and furniture drawer, and it is sold as a set of parts with its runner.

  • A thin steel side wipes out and does not swell, which is what a sink run needs.
  • A drawer that is stood in or climbed on needs a heavier system than this one.
  • An insert or a cutlery tray is quoted separately and is not part of the set.

The Limits

Nothing printed on the frames is a specification, so the numbers come from the order.

  • No length, no depth and no load figure appear on the frames, so all three are quoted against the cabinet opening.
  • The colour is a finish, not a steel grade; a grade is quoted on request.
  • The runner comes with the box, so a box on its own is not a complete drawer.

Ordering

The set is built to the opening, so the cabinet width, the drawer depth and the side depth are agreed first.

  • Give the cabinet opening, the drawer depth and which of the three sides with the enquiry.
  • Say how many drawers and which colour.
  • Screws and an insert are quoted with the order if they are wanted in the same carton.

What Buyers Call It

The same box is asked for under three names, and any of them reaches this drawer.

  • Ultra thin drawer box, when the wall thickness is the reason for the enquiry.
  • Slim drawer box system, when the drawer and its runner are being specified together.
  • Drawer box and runners, when the whole set is bought rather than the box on its own.

The H550 is an ultra thin drawer box in a low, mid or high side, with a panel bottom, a clipped front connector and its runner.

State the cabinet opening, the drawer depth and the side depth, and the sets are made and packed.

Who Makes The Box

The H550 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every drawer on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Can the three depths be mixed in one kitchen?

Yes. The low, mid and high side take the same front and the same runner, so a run can mix a shallow and a deep drawer.

How thin is the wall?

No wall thickness is printed on the frames, so it is quoted on the order against the opening rather than taken from a chart.

Is a runner included?

The set is quoted with its runner, because the runner length follows the cabinet depth.

Will a cutlery tray fit inside?

An insert can sit inside the box and is quoted separately. It is not part of the set.

What load does it carry?

The frames carry no load figure, so the rating is quoted on the order for the drawer the set is going into.