0
image
image
image
image
3 section drawer slides

Rebound Push Open Drawer Slide Black G-H312

G-H312
G-H312 is a black steel rebound drawer slide: a press on the drawer front releases the runner so the drawer opens without a handle, in three sections, side mounted and supplied in pairs.
Country of Origin
China
Quantity:
Contact Now
add to cart
All Products

The G-H312 Rebound Drawer Slide

The G-H312 is a rebound slide, which is the part that lets a drawer open with a press instead of a handle. The mechanism sits in the orange housing at the cabinet end, the rail is black, and the runner is three sections on steel balls.

G-H312 black rebound drawer slide pair with the orange rebound housing

At A Glance

ItemG-H312
MaterialSteel
TypeThree section ball bearing slide
ActionRebound, press to open
MountingSide mount
FinishBlack with orange housing
PackingPairs

How The Rebound Works

The housing holds a spring and a catch, and a press on the drawer front releases the catch so the spring pushes the drawer out.

  • A press of a few millimetres at the drawer front is enough to release the slide.
  • The slide pushes the drawer out for the first part of the travel, then the slide pulls as usual.
  • Push the drawer shut and the catch takes hold again, ready for the next press.

Why It Suits A Handleless Front

A handleless kitchen or wardrobe has nothing to pull, so the drawer has to be opened from the front itself.

  • The front stays clean, which is what a handleless run is bought for, and the slide stays hidden.
  • No handle means no drilling through the drawer front and no slide alignment to get wrong.
  • The rebound housing is the only part that shows, and it sits behind the front.

Three Sections, Full Travel

The three sections carry the drawer out over the full length of the runner, so the back of the drawer comes into reach.

  • The whole drawer box is accessible, which matters on a deep pan drawer.
  • Both outer sections stay supported at full travel, so the drawer does not dip at the end.
  • The runner screws to the side of the drawer box, which suits a standard cabinet build.
Close up of the G-H312 rebound housing and the black rail

Fitting It

The rebound is set off the front, so the gap between the drawer front and the carcass has to be right before the slide is finally tightened.

  • Set both slides on the drawer box and check the slide releases cleanly before the last screws go in.
  • Keep the screws in the slotted holes until the drawer runs true and the rebound releases cleanly.
  • Leave the housing end clear so the spring can push the drawer out.

The Limits

This is a cabinet slide and it is sold as one.

  • No load figure is printed on the frames, so the rating is quoted on the order rather than claimed here.
  • The slide is not a runner for a vehicle, a tool chest or an industrial rack.
  • A drawer that is stood in or climbed on needs a heavier slide.
The G-H312 slide flat along its length, black rails and housings

Ordering

The slide is matched to the cabinet, so the length and the front gap are agreed on the order.

  • Give the drawer depth and the thickness of the drawer front with the enquiry, and the slide is matched.
  • Say how many pairs, because the two slides of a pair are packed together.
  • Screws are quoted with the order if they are wanted in the same carton.

What Buyers Call It

The same slide is asked for under several names, and any of them reaches this part.

  • Rebound drawer slides, which is the trade name for the mechanism.
  • Push to open drawer slides, which is how the action is described on a retail page.
  • 3 section drawer slides, when the section count is what the order is specified on.

The G-H312 is a black steel rebound drawer slide, three section, side mount and supplied in pairs.

State the drawer depth and the front thickness, and the slide is checked before it is packed.

Who Makes The Slide

The G-H312 is made by Guangzhou Gorgeous Intelligent Technology Co., Ltd. and exported under the Gorgeous Hardware name: three production bases in Guangdong, stamping, ball assembly and finishing in house.

The panels below are the plant and the paperwork behind every slide on this page.

Eighty Countries, Six Numbers

Gorgeous Hardware world map of more than eighty export countries with six company statistics

Three Production Bases

Gorgeous Hardware factory gate and twelve production floor photographs from storage to container loading

The Certificates, And What Each One Covers

ISO 9001, ISO 14001 and ISO 45001 certificates with SGS, Intertek and RoHS test reports

Headquarters, Showrooms And Design

Guangzhou headquarters, hardware showroom, architectural display centre and design office

Where To Meet Us, March To December

Gorgeous Hardware trade show booths and the March to December exhibition calendar

Four Carton Options, And The Delivery Window

Four carton options from sticker service to OEM box and the six step delivery timeline

OEM, Brochures And Display

OEM logo on a hinge cup, brochure design pages and a branded display stand

Frequently Asked Questions

Does it need a handle?

No. The drawer front is pressed and the slide releases, which is the point of a handleless run.

Does it close softly as well?

This is the rebound part, so the press opens it and the catch holds it shut. A soft close damper is a different slide.

What length should I order?

The length follows the drawer depth, so give the depth with the enquiry and the slide is matched to it.

Are screws included?

No. Screws are quoted with the order if they are wanted in the same carton.

Is a load rating available?

The frames carry no load figure, so the rating is quoted on the order for the drawer it is going into.